UAD Console and outboard gear routing

[Huntero_Patricio]

I know this has been asked but I’m coming up short searching.
Inside console only Id like to send a signal to a rackmount guitar tuner. I basically just want a constant signal to the tuner, regardless what I do to the input the guitar is on.

id like to be able to mute the guitar in the console app, monitor from Pro Tools, but still have console sending the tuner a signal.

I’m using a x8p Line out 3 is going into the input of the tuner.

when I set the guitar track to output - line 3 in console I still hear it through the monitor. With and without mirror to monitor clicked I still hear it.

that and the tuner only receives signal if it’s unmuted. How can I monitor through pro tools and still output a signal to output line 3 while the console track is muted?

 

[UniversalAudio]

I know this has been asked but I’m coming up short searching.
Inside console only Id like to send a signal to a rackmount guitar tuner. I basically just want a constant signal to the tuner, regardless what I do to the input the guitar is on.

id like to be able to mute the guitar in the console app, monitor from Pro Tools, but still have console sending the tuner a signal.

I’m using a x8p Line out 3 is going into the input of the tuner.

when I set the guitar track to output - line 3 in console I still hear it through the monitor. With and without mirror to monitor clicked I still hear it.

that and the tuner only receives signal if it’s unmuted. How can I monitor through pro tools and still output a signal to output line 3 while the console track is muted?

Connect the tuner to a Cue that is mirrored to an out. This will get signal with the Console channel muted, DAW closed, etc.

 

[Huntero_Patricio]

Connect the tuner to a Cue that is mirrored to an out. This will get signal with the Console channel muted, DAW closed, etc.

I sent hi z channel 1 to the cue mix and mirrored the cue output to line out 3. That gets signal to the tuner but if i mute the track or pull the fader down it stops sending signal to the cue

 

[UniversalAudio]

I sent hi z channel 1 to the cue mix and mirrored the cue output to line out 3. That gets signal to the tuner but if i mute the track or pull the fader down it stops sending signal to the cue

Cues are pre fader so that should not be happening. And it's not what I see here. Can you make a vid of this happening?

 

[Nyoak34]

I sent hi z channel 1 to the cue mix and mirrored the cue output to line out 3. That gets signal to the tuner but if i mute the track or pull the fader down it stops sending signal to the cue

Make sure the cue is set to Pre

 

[Huntero_Patricio]

Connect the tuner to a Cue that is mirrored to an out. This will get signal with the Console channel muted, DAW closed, etc.

I was able to get it to work when mirroring the cue output to Line 3/4 by clicking CUE 1 instead of MIX under source in the CUE output menu. However now the singal is coming back into line 3 input and giving me level on track 3 inside console. Why is this?

 

[UniversalAudio]

I was able to get it to work when mirroring the cue output to Line 3/4 by clicking CUE 1 instead of MIX under source in the CUE output menu. However now the singal is coming back into line 3 input and giving me level on track 3 inside console. Why is this?

Do you have a virtual channel coming back to Console from the DAW??

Make a vid of this, we'll see the issue right away.

 

[Huntero_Patricio]

Do you have a virtual channel coming back to Console from the DAW??

Make a vid of this, we'll see the issue right away.

Trying to upload a video but it wont let me. Saying only accepted file extensions are audio and photo

 

[UniversalAudio]

Trying to upload a video but it wont let me. Saying only accepted file extensions are audio and photo

you'll need to use Dropbox or another hosting service.

 

[Huntero_Patricio]

you'll need to use Dropbox or another hosting service.

IMG_4042.MOV

drive.google.com

 

[UniversalAudio]

IMG_4042.MOV

drive.google.com

Check the normals on the bay. Mirroring to out 3 is likely normaled to in 3.

You can ignore or "dead patch" input 3 with a patch cable.

The patchbay was the missing variable.

 

[Huntero_Patricio]

Check the normals on the bay. Mirroring to out 3 is likely normaled to in 3.

You can ignore or "dead patch" input 3 with a patch cable.

The patchbay was the missing variable.

Im getting level on analog 3 in normal/half normal/ and thru. Hell it’s doing it even when just outputting. Pulled all cables from the output of the bay going back into the interface. Right now it’s just a single DB 25 cable going into the top of the back of the bay. Coming out of jack 3 on top going into jack 9 on bottom that has a single TRS cable going to the input of the tuner. Why does console think something’s coming back into input 3? When I switch analog 3 in console to Mic the signal stops.

 

[UniversalAudio]

Im getting level on analog 3 in normal/half normal/ and thru. Hell it’s doing it even when just outputting. Pulled all cables from the output of the bay going back into the interface. Right now it’s just a single DB 25 cable going into the top of the back of the bay. Coming out of jack 3 on top going into jack 9 on bottom that has a single TRS cable going to the input of the tuner. Why does console think something’s coming back into input 3? When I switch analog 3 in console to Mic the signal stops.

On the back of the Apollo, what's plugged into input 3?

 

[Huntero_Patricio]

On the back of the Apollo, what's plugged into input 3?

Nothing. Nothing in the combo jack and no DB25 either

 

[UniversalAudio]

Nothing. Nothing in the combo jack and no DB25 either

That's super weird.

You can start here:

https://help.uaudio.com/hc/en-us/articles/360051069631-UAD-Uninstall-Reinstall-Procedure-Windows

Looking at the vid again, I noticed channel 3 is set to Line. What happens when you sent it Mic?

Be also sure to get a ticket open with Support, they'll have things for you to try. Go to help.uaudio.com, click on the blue Support bot and type “create ticket”

 

[Huntero_Patricio]

That's super weird.

You can start here:

https://help.uaudio.com/hc/en-us/articles/360051069631-UAD-Uninstall-Reinstall-Procedure-Windows

Be also sure to get a ticket open with Support, they'll have things for you to try. Go to help.uaudio.com, click on the blue Support bot and type “create ticket”

thanks!

 

[UniversalAudio]

thanks!

Try the edit I posted above

 

[Huntero_Patricio]

When set to mic the signal goes away

Try the edit I posted above

 

[UniversalAudio]

When set to mic the signal goes away

And you're positive there is no d-sub in on the x8P? Sorry to belabor this but this the only way an x8P can be a line input.

 

[GED19904]

why dont you just get a cable splitter and save your output.